﻿Z14G3-BIOS release note:

R1.01:
1. Add Internal Speaker and Mic enable/disable

R1.00:
1. CPU VR cuurent limit from 100-> 0(auto)
2. Lid open , system will wake camera

RC.02:
1. Fix GPS only, can not power it.
2. Disable 5G card wake function on ME
3. Fix Serial port test fail issue
4. Add Enable/disable Expansion board on Setup/menu
5. Fix PCIE port E(SSD), modify EQ EQ settings for can detect some SSD
6. modify USCI delay timer

RC.01:
1. Add espi com port
2. Expresscard speed= gen1
3. Fix 5G fail issue
4. Add Retimer capsule update
5. Update ME and TBT new FW
6. Change panel brightness
7. Modify "USB type C" to enable/disable for usb and pcie function

RC.00
1. Add Retimer capsule update fuction

RB.04
1. Fix "Battery show 0% somtimes"
2. For 3D mark test, change Acoustic noise setting, GT current and Memory overclock Voltage settings

RB.03
1. change TBT mode from "OS" to "Firmware" for SSD fail
2. Fix Battery calibration fail
3. Fix Rb.02 MXM fail issue

RB.02
1. Add AMR and iST function in ME, need to install driver
2. Panel brightness * 0.85
3. Add Acuistic settings of CPU VR for DRAM

RB.01
1. for GPS only
2. Add Uart2 mode
3. SD cARD EN/DIS

RA.15
1. Change "Thunderbolt enable/disable" to "USB Type C enable/disable"
2. disable clock request 8

RA.14
1. Add IR camera settings
2. add USB OC table

RA.13
1. fix TBt fail RA.12
2. fix modern standby when RFID disable

RA.12
1. Add Boot guard
2. Add thunderbolt enable/disable in advanced menu
3. change "USB power sharing" to "USB always on charging"
4. fix LAN 219 disable, windows will reboot
5. Add UCSI function
6. brightness 20% during POST
7. RFID will turn off when system enter MS

RA.11
1. for Modern standby
2. Fix MXM fan and RTD3 cold

RA.10
1. Check PD power to warning message.
2. Support WiFi7

RA.10
1. BIOS code base from version 17 to 19 for DRAM MRC version 1.1.14 to 1.13.14
2. Fix two battery calibration issue

RA.09
1. BIOS code base from version 17 to 19 for DRAM MRC version 1.1.14 to 1.13.14
2. Fix two battery calibration issue

RA.08
1. fix Battery calibration for 2 battery
2. Set B16 to native2
3. add quick menu interface
4. remove user password
5. Tcc offset=20
6. Set Pl1=68000 pl2=85000 pl3=85000 pl4=110000
7. Set HDMI port for HDMI 2.1

RA.07
1. Set POST panel=brightness=128
2. Set HDA SVID and SSID
3. Disable BT offload  disable for MIC of BT
4. modify battery calibration for 2 battery
5. add quick menu interface
6. Set GPp_16 to native2

RA.06
1. add panel brightness table
2. Fix camera mirror issue
3. fix usb2 port warning issue
4. add second battery in system
5. Psys=992
6. add usb port disable/enable
7. fix RFID enable, but it is disable

RA.05
1. add power event
2. Add expresscard power
3. add expresscard hotplug event
4. add KB backlgiht 
5. Add RTC wakeup

RA.04
1. EC H2 RAM Base change to FE420000 EC version use r00.01.01.09
2. Add setup menu device enable/disable function
3. modify P1/P2 function
4. add PXE function
5. Change GPP_A21 to native1
